Bevel gearboxes and flanged bevel gearboxes for indicators

Home > Products > Transmission of motion, regulation of speed and position, lifting, displacement and alignment > Bevel gearboxes and flanged bevel gearboxes for indicators > 66/5UC

Tutti i prodotti

66/5UC

Continuous use gearbox

66/5UC

Continuous use gearbox

• Ideal for continuous motorized use at maximum efficiency, without any loss of power.
• The component configuration ensures handling of constant loads with smooth, and uninterrupted operation.
• Oil bath lubrication for speeds above 200 rpm; grease lubrication for speeds below 200 rpm.
• Available transmission ratios: 1:1 - 1:2 - 2:1 (available in versions «A»-«B»-«C»).
• Aluminium case, anodised; AISI 303 stainless steel shafts.
• Max. transmissible torque 14 Nm.
• Models:
- Version «A» with 2 outputs; weight 600 g.
- Version «B» with 3 outputs; weight 620 g.
- Version «C» (opposite rotation) with 3 ouputs; weight 630 g.
- Version «D» with 3 outputs, 2 through hollow shafts; weight 590 g.
• Standard shafts: M = male Ø10CH3 / F = female Ø10CH3.
Available on request:
▪ Shafts: M = male Ø14CH5 in versions.
▪ Shafts: F = female Ø14CH5 in versions.
▪ Custom configurations.

Photogallery

VERSION WITH DIMENSION DRAWINGS

Available shafts

male shaft M

female shaft F

through-hollow female shaft F

Version «A» M-M

Version «A» M-F

Version «A» F-M

Version «A» F-F

Version «B» M-M-M

Version «B» F-M-M

Version «C» M-M-M

Version «C» M-F-F

Version «C» F-M-M

Version «C» F-F-F

Version «D» F-F-F

Version «D» M-F-F

REPRESENTATION OF DIRECTION OF ROTATION
«A»	«B»

«C»	«D»

The direction of rotation depends from the configuration and from the positioning; see “Versions with dimension drawings”.

REPRESENTATION OF DESIGN CONFIGURATION

The desing configuration is determined by the shaft1always shown on the opposite side of the fixing bores M_, the others shaft are defined following the clockwise direction.

REPRESENTATION OF TRANSMISSION RATIOS

The ratio is determined by the shaft1always shown on the opposite side of the fixing bores M_.

PHASE BETWEEN KEYS
ratio	degrees °
1/1	± 8,5°
1/2	± 5,5°
2/1	± 5,5°
a. keyway b. key
The keyways on the shafts are never perfectly in phase, except for shaft 2 and 3 in versions «B» and «D».

GUIDELINES

Selection of the gearbox

For correct sizing it is necessary to identify: the power, the torque and the rotation speed. We advise to consult also the tables, and the technical data shown in the “General Information” (p. 4 - 7).
For abbreviations and acronyms consult the "glossary" (p. 7)

Installation

Ensure proper alignment of the shafts to avoid overloading, overheating, and premature wear of the bearings. The gearboxes, thanks to their construction design, can be installed in any position.

Start-up

After a brief pre-delivery test, the gearbox requires several hours of running to reach maximum efficiency. A gradual increase in load is recommended, reaching full load within 20-30 hours of operation. Initial temperatures will be higher during the break-in period.

Periodic maintenance

Our gearboxes are maintenance-free; however, it is advisable to periodically check for any lubricant leaks. The replacement of the gearbox depends on operating conditions, with an estimated lifespan of 10,000 hours under normal conditions.

Storage

During warehouse storage, protect the gearboxes from dust and corrosive environments. We recommend periodically rotating the gearboxes to ensure proper lubrication of internal parts and seals.

Warranty

The warranty is valid only if all instructions provided in the catalog are strictly followed.