Bevel gearboxes and flanged bevel gearboxes for indicators

Home > Products > Transmission of motion, regulation of speed and position, lifting, displacement and alignment > Bevel gearboxes and flanged bevel gearboxes for indicators > 66/4

Tutti i prodotti

66/4

Gearboxes for intermittent use

66/4

Gearboxes for intermittent use

• Available transmission ratios: 1:1 - 1:2 (standard) - 2:1 (available in versions «A»-«B»-«C»).
• Ratios 1/2 and 2/1 are only available with spiral gears.
• Aluminium case, anodised; stainless steel shafts (standard).
• Torque 4 Nm. Radial load 15 kg - axial load 1,5 kg.
• Models:
- Version «A» with 2 outputs; weight 145 g.
- Version «B» with 3 outputs; weight 160 g.
- Version «C» (opposite rotation) with 3 ouputs; weight 170 g.
- Version «D» with 3 outputs, 2 through hollow shafts; weight 160 g.
- Version «E» with 4 outputs; weight 220 g.
• Standard output shafts: M = male Ø8 / F = female Ø8.
Available on request:
▪ Output shafts: male / female Ø10 - Ø12 - Ø14 in versions «A»-«B»-«C».
▪ Case in stainless steel AISI 303.
▪ Models with spiral bevel gears are available in all versions with transmission ratio 1/1.
▪ Machine-side coupling flange FL-M.
▪ Male shaft flange for position indicators FL-OP/EP.

Photogallery

AVAILABLE SHAFTS
M = male

F = female

F = female through shaft (available only on versione ⟪D⟫)

DIMENSIONS

VERSION ⟪A⟫ - M-M

VERSION ⟪A⟫ - M-F

VERSION ⟪A⟫ - F-F

VERSION ⟪B⟫ - M-M-M

VERSION ⟪B⟫ - F-M-M

VERSION ⟪C⟫ - M-M-M with opposite rotation

VERSION ⟪C⟫ - M-F-F with opposite rotation

VERSION ⟪C⟫ - F-M-M with opposite rotation

VERSION ⟪C⟫ - F-F-F with opposite rotation

VERSION ⟪D⟫ - M-F-F with through-hollow shaft

1. n° 2 screws M4
2. with through-hollow shaft

VERSION ⟪D⟫ - F-F-F with through-hollow shaft

1. n° 2 screws M4
2. with through-hollow shaft

VERSION ⟪E⟫ - M-M-M-M

VERSION ⟪E⟫ - F-F-F-F

1. n° 2 screws M4
2. with through-hollow shaft

CONFIGURATION AND DIRECTION OF ROTATIO
⟪A⟫	⟪B⟫	⟪C⟫

⟪D⟫	⟪E⟫

The direction of rotation depends from the configuration and from the positioning.

REPRESENTATION OF BEVEL GEARS
Straight bevel gears		Spiral bevel gears ‹SP›

Suitable for moderate loads and speeds		Suitable for loads + 30% and high speeds

REPRESENTATION OF TRANSMISSISSION RATIOS

The ratio depends on shaft ‹1› shown opposite the fixing bores M_
example: ratio 1:2	example: ratio *2:1
shaft 1 = 10 rpm	shaft 1 = 5 rpm
shaft 2 = 5 rpm	shaft 2 = 10 rpm
	* not available in version «D»

RAFFREPRESENTATION OF DESIGN CONFIGURATION

The design depends on shaft 1opposite the fixing bores M_; others shafts follow clockwise.

REPRESENTATION OF LOADS
«B»	«D»

Fr = radial load 150 N The radial load is applied perpendicular to the axis of the shaft. Fa = axial load 15 N The axial load (push or pull) acts along the direction of the shaft. T = torque 4 Nm
Note: a radial load (ex. belt tension) can only be applied to the long shaft of the «B» and «D» versions; otherwise, a support must be provided.

COUPLING BUSHES 2 piece bushing to couple gearboxes and shafts.

Available bores Ø: 6 - 8 -10 -14.
➜ for more complete information, see BT

Support units (with square flange) with o.ring, and ball-bearings.

• Available shafts Ø6, Ø8, Ø10, Ø14, Ø20.
➜ for more complete information, see Supports

Flanged supports with extension shaft for coupling with position indicators.
➜ for more complete information, see Flanged supports

The «GC» and «GCC» cardan joints used for the transmission of torque and movement of non-aligned elements.
Main features: universal application, high reliability, maintenance free, extremely precise and ease-of-use.
• Case entirely machined from solid, in stainless steel AISI303.
• Suitable for intermittent (UI) and continuous movements (UC).
• Maximum working angle 45 °.

➜ for more complete information, see GC and GCC

• The telescopic shafts are ideal to connect two elements with a constant or variable center to center distance.
• Suitable for adjustments and for continuous use.
• Torque from 5 Nm to 10 Nm.

➜ for more complete information, see ATE

• 4 digits counter (standard red digit indicates decimals; on request 2 red digits for hundredths or 4 black digits for mm). Reading until 9999.Digit height 5 mm
• Standard shaft bore: ø14H7; other bores, smaller than 14 with reducing bush.
➜ for more complete information, see OP3

The EP3 electronic indicator allows monitoring of adjustments to eliminate errors and a precise reading of linear or angular displacements.
• 100% interchangeable with mechinal indicator OP3.
• Powered by a long-life battery, easy replacement from the front.
• Hollow shaft made of stainless steel; shock, vibration and dirt resistant plastic case.
➜ for more complete information, see EP3

The flange FL-M, compatible with any configuration and output shaft (male or female) of the gearbox, ensures a stable and precise coupling, minimizing vibrations and ensuring correct alignment between the connected components. Made of black anodized aluminum, it is coordinated with the gearbox case, also in black.

FL-M

Configuration examples
Gearbox with 2 shafts	Gearbox with 3 shafts

Male shaft with flange MØ14x68 FL-OP3/EP3, compatible with any configuration and output shaft of the gearbox, connects the position indicator, whether mechanical or electronic, to the gearbox. This combination enables precise and monitored position adjustment, increasing stability and accuracy of readings. Made of black anodized aluminum, it is coordinated with the gearbox case, also in black.